series amer63-kz 700ma | ac-dc led driver www.aimtec.com tel: +1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 052.1e r1.c 1 of 2 north america only features: models single output model max output power (w) * output voltage range (v) output current (ma) input voltage (vac/hz) efficiency (%) AMER63-9070KZ 65.7 65-90 700 30 90-264/ 47-63 85 * exceeding the maximum output power w ill permanently damage the converter note: all specifications in this datasheet are measured at an ambient temperature of 25c, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. input specifications parameters conditions typical maximum units voltage range 90-264 vac inrush current <2ms 115v 20 a 230v 30 leakage current 230v 0.25 ma ac current 115v 0.5 a 230v 0.35 no-load consumption 2.5 w external fuse 250v/2.5a output specifications parameters conditions typical maximum units current accuracy 5 % line regulation 5 % load regulation 10 % ripple & noise 100 mv p-p hold-up time (min) 6 10 ms isolation specifications parameters conditions typical maximum units tested i/o voltage 5ma/60sec 3000 vac input to case 3000 vac isolation resistance >50 m ? general specifications parameters conditions typical maximum units switching frequency 65 khz over current protection 115 % over voltage protection zener diode clamp short circuit protection continuous short circuit restart auto-recovery operating temperature * -30 to +55 o c maximum case temperature 95 o c storage temperature -40 to +80 o c temperature coefficient 0.05 % / o c cooling free air convection ? ac-dc constant current led driver ? waterproof ip67 ? universal input: 90-264vac, 47-63hz ? over current protection ? short circuit protection ? over voltage protection ? rohs compliant ? low output ripple
series amer63-kz 700ma | ac-dc led driver www.aimtec.com tel: +1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 052.1e r1.c 2 of 2 north america only general specifications (continued) parameters conditions typical maximum units humidity 95 % rh case material aluminum weight 750 g dimensions (l x h x w) 5.91 x 2.68 x 1.97 inches 150.00 x 68.00 x 50.00 mm mtbf 50,000 hrs (mil-hdbk-217 f at +25 o c) * note: converters do not have over temperature protection and will be damaged if their maximum case temperature is exceeded . safety specifications parameters agency approvals ce standards gb195110.1-2004/iec61347-1:2003, en55015, en61000, en61547 dimensions 50.00 (1.97) side view 1.00 (0.04) 150.00 (5.90) 68.00 (2.68) 120.00 (4.72) 15.00 (0.59) 136.00 (5.35) top view 50.00 (1.97) 20.00 (0.79) 10.00 (0.39) 4.00 (0.16) 200.00 (8.00) output wires are 18awg at 20cm 200.00 (8.00) input wires are 18 awg at 20cm 15.00 (0.59) note: 1. datasheets are updated as needed and as such, specifications ar e subject to change without notic e. once printed or downloaded , datasheets are no longer controlled by aimtec; refer to www.aimtec.com for the most current product specifications. 2. product labels shown, including safety agency cert ifications on labels, may vary based on the date manufactured. 3. mechanical drawings and specifications are for reference only. 4. all specifications are measured at an am bient temperature of 25c, humidity<75%, nominal input voltage and at rated output load unless otherwise specifie d. 5. aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. cas numbers and other limited information are considered proprietary an d may not be available for release. 6. this product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control sys tems or other such applications which necessitate specific safety and regulatory standards ot her the ones listed in this datasheet. 7. warranty is in accordance with aimtec?s st andard terms of sale available at www.aimtec.com.
|
